ASTM A192/A192M Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service.ASTM A192/A192M高壓用無縫碳鋼鍋爐管標準規範。

ASTM A192/A192M guide covers standard specifications for minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service. The steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, and silicon. The tubes shall have a hardness number not exceeding a specific value. The following mechanical tests shall be conducted, namely: flattening test; flaring test; hardness test; and hydrostatic test.

ASTM A192/A192M指南涵蓋了高壓用無縫碳鋼鍋爐和過熱器管的最小壁厚標準規範。鋼應符合碳、錳、磷、硫和矽所需的化學成分。管子的硬度值不得超過特定值。應進行以下機械試驗，即：平整試驗；燃燒試驗；硬度試驗；水壓試驗。

What is ASTM A192? ASTM A192是什麽？

ASTM A192 is a standard for seamless carbon steel boiler and superheater tubes with minimum wall thickness for high-pressure applications. The standard is issued under the fixed designation A 192/A 192M. It is under the jurisdiction of ASTM Committee A01 on Steel. 

ASTM A192是高壓應用中最小壁厚的無縫碳鋼鍋爐和過熱器管的標準。該標準以固定名稱A 192/A 192M發布。它由ASTM鋼委員會A01管轄。

ASTM A192 is generally used for high-pressure boilers with a working pressure that does not exceed 9.8Mpa. The tubes are available in hot rolled and cold drawn delivery states. 

ASTM A192通常用於工作壓力不超過9.8Mpa的高壓鍋爐。這些管子有熱軋和冷拔兩種交付狀態。

ASTM A192 Seamless Steel Tube ASTM A192無縫鋼管

ASTM A192 Seamless Steel Tube is applied as minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service. 

ASTM A192無縫鋼管作為最小壁厚，用於高壓服務的無縫碳鋼鍋爐和過熱器管。

Scope範圍

1. 1. This specification2 covers minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service. 
   2. 1.1本規範涵蓋了高壓用無縫碳鋼鍋爐和過熱器管的最小壁厚。

1.2 The tubing sizes and thicknesses usually furnished to this specification are 1/2 in. to 7 in. [12.7 to 177.8 mm] outside diameter and 0.085 to 1.000 in. [2.2 to 25.4 mm], inclusive, in minimum wall thickness. Tubing having other dimensions may be furnished, provided such tubes comply with all other requirements of this specification. 

1.2本規範中通常提供的管材尺寸和厚度為外徑1/2英寸至7英寸[12.7至177.8毫米]，最小壁厚為0.085至1.000英寸[2.2至25.4毫米]。可以提供具有其他尺寸的管子，前提是這些管子符合本規範的所有其他要求。

1.3 Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] inside diameter or 0.015 in. [0.4 mm] thickness. 

1.3機械性能要求不適用於內徑小於1/8英寸[3.2毫米]或厚度小於0.015英寸[0.4毫米]的管子。

1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 

1.4以英寸-磅單位或國際單位表示的值應單獨視為標準值。在文本中，國際單位製顯示在括號中。每個係統中所述的值不是完全等效的；因此，每個係統都必須獨立使用。將兩個係統的值結合起來可能會導致不符合規範。除非訂單中指定了本規範的“M”名稱，否則應采用英寸-磅單位。

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

1.5本國際標準是根據世界貿易組織技術性貿易壁壘委員會發布的《關於製定國際標準、指南和建議的原則的決定》中確立的國際公認的標準化原則製定的。

What is the chemical composition of ASTM A192?  ASTM A192的化學成分是什麽？

ASTM A192/A192M Mechanical Properties  ASTM A192/A192M機械性能

What is the yield strength of ASTM A192?  ASTM A192的屈服強度是多少？

The tensile strength and yield strength of the ASTM A192/ ASME SA-192 tube are 325 MPa and 180 MPa at room temperature, respectively. 

ASTM A192/ASME SA-192管在室溫下的抗拉強度和屈服強度分別為325 MPa和180 MPa。

*T.S.: tensile strength; *Y.S.: yield strength; *El.: elongation. 

TS.：抗拉強度*Y.S.：屈服強度*El：伸長。
*The Brinell Hardness number applies to ASTM A192 tubes 0.200″ [5.1 mm] and over in wall thickness.

布氏硬度值適用於壁厚為0.200英寸[5.1毫米]及以上的ASTM A192管。
*The Rockwell Hardness number applies to ASTM A192 tubes less than 0.200″ [5.1 mm] in wall thickness.

洛氏硬度值適用於壁厚小於0.200英寸[5.1毫米]的ASTM A192管。
*Mechanical properties don’t apply to tubing smaller than 1/8″ [3.2 mm] inside diameter or 0.015″ [0.4 mm] thickness.

*機械性能不適用於內徑小於1/8英寸[3.2毫米]或厚度小於0.015英寸[0.4毫米]的管子。

ASTM A192/A192M Mechanical Tests Required    ASTM A192/A192M要求的機械試驗

Flattening test, flaring test, hardness test, hydrostatic test, and tension test.  壓扁試驗、擴口試驗、硬度試驗、水壓試驗和拉伸試驗。

Carbon Steel ASTM A192 / ASME SA192 Tubes Equivalent Grades  ASTM A192/ASME SA192碳鋼管等效格柵

ASTM A 192 boiler tube equivalent EN 10216-2, DIN 17175, BS 3059 Part II, NF A 49-213, NBR 5594 ASTM (American Society for Testing Materials standard) A192 and ASME (American Society of Mechanical Engineers standards) SA192. Equivalent Materials 1010, St35.8, 360. FASTWELL has standard specifications for minimum-wall-thickness, seamless carbon steel boiler and super heater tubes for high-pressure service.

ASTM A 192鍋爐管相當於EN 10216-2、DIN 17175、BS 3059第二部分、NF A 49-213、NBR 5594 ASTM（美國材料試驗學會標準）A192和ASME（美國機械工程師學會標準）SA192。等效材料1010，St35.8360。FASTWELL具有最小壁厚、無縫碳鋼鍋爐和高壓過熱器管的標準規格。

ASTM A192/A192M Pressure Rating ASTM A192/A192M壓力等級

Maximum working pressure of ASTM A192 Tube at temperature 400°F, The dimensions - outside pipe diameters and wall thicknesses are according ANSI B36.10.

ASTM A192管材在400°F溫度下的最大工作壓力，尺寸——外徑和壁厚符合ANSI B36.10。

What is SA 192 equivalent to? SA 192等於什麽？

The ASTM A192/ASME SA192 standard is applicable to seamless carbon steel pipes used for boilers and superheaters in high-pressure environments, with a focus on meeting the minimum wall thickness necessary for these applications.

ASTM A192/ASME SA192標準適用於高壓環境中用於鍋爐和過熱器的無縫碳鋼管，重點是滿足這些應用所需的最小壁厚。

ASTM A 192 boiler tube equivalent EN 10216-2, DIN 17175, BS 3059 Part II, NF A 49-213, NBR 5594 ASTM (American Society for Testing Materials standard) A192 and ASME (American Society of Mechanical Engineers standards) SA192. Equivalent Materials 1010, St35.

ASTM A 192鍋爐管相當於EN 10216-2、DIN 17175、BS 3059第二部分、NF A 49-213、NBR 5594 ASTM（美國材料試驗學會標準）A192和ASME（美國機械工程師學會標準）SA192。等效材料1010，St35。

American Standard A192/SA192 Seamless Carbon Steel Boiler and Superheater Tubes for High Pressure Minimum Wall Thicknesses 

美國標準A192/SA192高壓用無縫碳鋼鍋爐和過熱器管最小壁厚

ASTM A192/A192M - Industries & Applications    ASTM A192/A192M-工業和應用

Our ASTM A192/A192M are widely used in various industries due to their excellent properties and performance. Some of the key industries and applications where ASTM A192 tubes find extensive use include:

日皮视频在线观看的ASTM A192/A192M因其優異的性能和性能而廣泛應用於各個行業。ASTM A192管材廣泛使用的一些關鍵行業和應用包括：

• Gas Processing Industries 天然氣加工行業
• Petrochemical Industries石化行業
• Power Generation Industries發電行業
• Food Processing Industries食品加工業
• Chemical Industries化學工業
• Oil & Gas Industries石油和天然氣行業
• Fertilizers Industries化肥行業
• Sugar Industries糖業